Specification Weight: 30-31KG Overall Dimensions: 390mm×350mm×235mm Power: 160-300W   Mode of Display: LCD Liquid Crystal Display Screen     Cutting Length: 1mm - 9999mm   Cutting Tolerance:≤0.002×L (L = Cutting Length)      Stripping Length: Head 0 - 35mm ,Tail 0- 15mm  Cutting Cross-sectional Area of Wire Core: (508C 0.2-2.5 mm2    508-SD 0.1- 4.5mm2  ) (508E 0.1-8 mm2    508-JE 0.1- 10mm2  ) Maximum Diameter of Conduit Pipe: ¢11 Middle-stripping: 10 places of strippingÂ
Material of Knife: High-quality Tungsten SteelÂ
Stripping Speed:
3000 - 80000 p c s /hÂ
Mode of Driving:
Mode C Two-wheeled Drive
Mode SD/SDB/E/JE Four-wheeled Drive
Adjusting Speed:
0 Slowest, 9 Fastest   Â
Operating Principle
The wire is conveyed through the wire-inlet rollers and the wire-outlet rollers and the wire cutting and stripping is finished through the knife rack assembly, which are all controlled by microcomputer technology.
Introduction to Main Function of Every Part
1. Wire-inlet Rollers: for conveying wires and stripping wire heads. 2. Wire-outlet Rollers: for conveying wires and stripping wire tails. 3. Knife Rack Assembly: for wire cutting, head stripping and tail stripping. 4. Wire-inlet Gap Adjusting Rollers: for adjusting the wire-inlet gap, turn it down to decrease the gap and turn it up to increase the gap. 5. Wire-outlet Gap Adjusting Rollers: for adjusting the wire-outlet gap, turn it up to increase the gap and turn it down to decrease the gap. 6. Conduit Pipe Assembly: for ensuring the wire smooth and straight and preventing the wire from moving defectively when the wire moves from the wire-inlet rollers to the knife rack assembly.Â
Key Points for Operation of Mechanical Parts
1. The wire is put into the wire inlet, through the wire-inlet rollers and the conduit pipe, and then onto the knife edge.   2. Wire-inlet Gap Adjusting: adjust the gap between the two rollers through the wire-inlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped so as to ensure normal stripping of wire covering.  3. Wire-outlet Gap Adjusting: adjust the gap between the two rollers through the wire-outlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped, and adjust the indicator light of wire breakage at the critical state between on and out, then turn up for half circle. If the machine still stops because the wire knobs, adjust the gap a little smaller.Â
Â
Specification Weight: 30-31KG Overall Dimensions: 390mm×350mm×235mm Power: 160-300W   Mode of Display: LCD Liquid Crystal Display Screen     Cutting Length: 1mm - 9999mm   Cutting Tolerance:≤0.002×L (L = Cutting Length)      Stripping Length: Head 0 - 35mm ,Tail 0- 15mm  Cutting Cross-sectional Area of Wire Core: (508C 0.2-2.5 mm2    508-SD 0.1- 4.5mm2  ) (508E 0.1-8 mm2    508-JE 0.1- 10mm2  ) Maximum Diameter of Conduit Pipe: ¢11 Middle-stripping: 10 places of strippingÂ
Material of Knife: High-quality Tungsten SteelÂ
Stripping Speed:
3000 - 80000 p c s /hÂ
Mode of Driving:
Mode C Two-wheeled Drive
Mode SD/SDB/E/JE Four-wheeled Drive
Adjusting Speed:
0 Slowest, 9 Fastest   Â
Operating Principle
The wire is conveyed through the wire-inlet rollers and the wire-outlet rollers and the wire cutting and stripping is finished through the knife rack assembly, which are all controlled by microcomputer technology.
Introduction to Main Function of Every Part
1. Wire-inlet Rollers: for conveying wires and stripping wire heads. 2. Wire-outlet Rollers: for conveying wires and stripping wire tails. 3. Knife Rack Assembly: for wire cutting, head stripping and tail stripping. 4. Wire-inlet Gap Adjusting Rollers: for adjusting the wire-inlet gap, turn it down to decrease the gap and turn it up to increase the gap. 5. Wire-outlet Gap Adjusting Rollers: for adjusting the wire-outlet gap, turn it up to increase the gap and turn it down to decrease the gap. 6. Conduit Pipe Assembly: for ensuring the wire smooth and straight and preventing the wire from moving defectively when the wire moves from the wire-inlet rollers to the knife rack assembly.Â
Key Points for Operation of Mechanical Parts
1. The wire is put into the wire inlet, through the wire-inlet rollers and the conduit pipe, and then onto the knife edge.   2. Wire-inlet Gap Adjusting: adjust the gap between the two rollers through the wire-inlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped so as to ensure normal stripping of wire covering.  3. Wire-outlet Gap Adjusting: adjust the gap between the two rollers through the wire-outlet gap adjusting rollers to make the gap less than the outer diameter of the wire to be stripped, and adjust the indicator light of wire breakage at the critical state between on and out, then turn up for half circle. If the machine still stops because the wire knobs, adjust the gap a little smaller.Â
